forumpoweraudio.ro

The SD12-1000EL is a high output wide bandwidth transducer designed for low frequency response in two way designs and for high output mid bass. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies. This design is optimized for both live sound and recorded music venues. The transducer uses high energy neodymium magnetics to achieve a very high acoustic output to weight ratio. The SD12-1000EL has been optimized for use in two and three way sound reinforcement system designs and may be used in either mid bass or low frequency applications. The operating bandwidth is 60Hz to 3000Hz. The SD12-1000EL employs a large 4 inch (101.6mm) diameter voice coil that provides an AES rated 1000 watts of continuous power handling and a full 4000 watts of peak rated power handling when sufficient amplifier headroom is available. The SD12-1000EL utilizes P Audios Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is an inside/outside geometry with P Audios square wire technology to improve conversion efficiency and provide a very large cross-sectional area for superior cooling. System linearity is achieved by employing magnetic flux demodulation devices in the structure to increase fidelity and sonic accuracy. The system suspension has been designed specifically for high linear displacement for both low frequency and mid band response. The double spider design insures very high displacement and linear response while maintaining excellent control. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

The SD15-1700EL is a high output wide bandwidth transducer. The 15 inch (381mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies and is ideal for high level low frequency response in two and three way systems. This design is an excellent component for both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The SD15-1700EL has been optimized for use in two and three way sound reinforcement system designs. The operating bandwidth is 55Hz to 2000Hz. The SD15-1700EL employs a very large 4.5 inch (114.3mm) diameter voice coil that provides an AES rated 1700 watts of continuous power handling and a full 6800 watts of peak rated power handling when sufficient amplifier headroom is available. The SD15-1700EL utilizes P Audios Auto Balanced-Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is an inside/outside geometry with P Audios square wire technology to improve conversion efficiency and provide a very large cross-sectional area for superior cooling. System linearity is achieved by employing magnetic flux demodulation devices in the structure to increase fidelity and sonic accuracy. The system suspension has been designed specifically for high linear displacement and extended low frequency response and high level output in multi-way system designs. The double spider design insures very high displacement and linear response while maintaining excellent control The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

The SD15-1700N is a high output wide bandwidth transducer. The 15 inch (381mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies and is ideal for high level low frequency and full range response. This design is optimized for both live sound and recorded music venues. The transducer uses high energy neodymium magnetics to achieve a very high acoustic output to weight ratio. The SD15-1700N has been optimized for use in two and three way sound reinforcement system designs. The operating bandwidth is 55Hz to 2000Hz. The SD15-1700N employs a large 4.5 inch (114.3mm) diameter voice coil that provides an AES rated 1700 watts of continuous power handling and a full 6800 watts of peak rated power handling when sufficient amplifier headroom is available. The SD15-1700N utilizes P Audios Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is an inside/outside geometry with P Audios square wire technology to improve conversion efficiency and provide a very large cross-sectional area for superior cooling. System linearity is achieved by employing magnetic flux demodulation devices in the structure to increase fidelity and sonic accuracy. The system suspension has been designed specifically for high linear displacement for both low frequency and mid band response. The double spider design insures very high displacement and linear response while maintaining excellent control. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

The SD18-1700EL is a high output low frequency transducer. The 18 inch (457mm) diameter piston will produce extremely high sound pressure levels at very low frequencies and is ideal for high level deep bass and sub woofer response in both live sound and recorded music venues. The operating range is 30Hz to 200Hz. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The SD18-1700EL employs a very large 4.5 inch (114.3mm) diameter voice coil that provides an AES rated 1700 watts of continuous power handling and a full 6800 watts of peak rated power handling when sufficient amplifier headroom is available. It is recommended that the transducer be loaded into a properly designed vented enclosure and that active high order high pass filtering be employed if extremely high power levels are expected at low frequencies. The SD18-1700EL utilizes P Audios Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is an inside/outside geometry with P Audios square wire technology to improve conversion efficiency and provide a very large cross-sectional area for superior cooling. System linearity is achieved by employing magnetic flux demodulation devices in the structure to increase fidelity and sonic accuracy. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The double spider design insures very high displacement and linear response while maintaining excellent control. The cone has been treated with a conformal coating designed to provide additional mechanical damping and moisture resistance. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

The SD18-1700N is an very high output low frequency transducer. The 18 inch (457mm) diameter piston will produce extremely high sound pressure levels at very low frequencies and is ideal for high level deep bass and sub woofer response in both live sound and recorded music venues. The operating range is 30Hz to 200Hz. The transducer uses high energy neodymium magnetics to achieve a very high acoustic output to weight ratio. The SD18-1700N employs a large 4.5 inch(114.3mm) diameter voice coil that provides an AES rated 1700 watts of continuous power handling and a full 6800 watts of peak rated power handling when sufficient amplifier headroom is available. It is recommended that the transducer be loaded into a properly designed vented enclosure and suitable active high pass filtering be employed if extremely high power levels are expected at low frequencies. The SD18-1700N utilizes P Audios Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is an inside/outside geometry with P Audios square wire technology to improve conversion efficiency and provide a very large cross-sectional area for superior cooling. System linearity is achieved by employing magnetic flux demodulation devices in the structure to increase fidelity and sonic accuracy. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The double spider design insures very high displacement and linear response while maintaining excellent control. The cone has been treated with a conformal coating designed to provide additional mechanical damping and moisture resistance. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

The SD21-1800EL is a high output low frequency transducer. The 21 inch (533mm) diameter piston will produce extremely high sound pressure levels at very low frequencies and is ideal for high level deep bass and sub woofer response in both live sound and recorded music venues. The very large radiating area and high linear displacement insure extremely high acoustic power radiation at very low frequencies. The operating range is 30Hz to 200Hz. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The SD21-1800EL employs a very large 5 inch (127mm) diameter voice coil that provides an AES rated 1800 watts of continuous power handling and a full 7200 watts of peak rated power handling when sufficient amplifier headroom is available. It is recommended that the transducer be loaded into a properly designed vented enclosure and that active high pass filtering be employed if extremely high low frequency power input will be used. The SD21-1800EL utilizes P Audios Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is an inside/outside geometry with P Audios square wire technology to improve conversion efficiency and provide a very large cross-sectional area for superior cooling. System linearity is achieved by employing magnetic flux demodulation devices in the structure to increase fidelity and sonic accuracy. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The double spider design insures very high displacement and linear response while maintaining excellent control. The cone has been treated with a conformal coating designed to provide additional mechanical damping and moisture resistance. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

The SD21-1800N is an ultra high output low frequency transducer. The 21 inch (533mm) diameter piston will produce extremely high sound pressure levels at very low frequencies and is ideal for high level deep bass and sub woofer response in both live sound and recorded music venues. The 21 inch piston area will produce extremely high acoustic output power. The operating range is 30Hz to 200Hz. The transducer uses high energy neodymium magnetics to achieve a very high acoustic output to weight ratio. The SD21-1800N employs a very large 5 inch (127mm) diameter voice coil that provides an AES rated 1800 watts of continuous power handling and a full 7200 watts of peak rated power handling when sufficient amplifier headroom is available. It is recommended that the transducer be loaded into a properly tuned vented enclosure for maximum power handling. The SD21-1800N utilizes P Audios Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is an inside/outside geometry with P Audios square wire technology to improve conversion efficiency and provide a very large cross-sectional area for superior cooling. System linearity is achieved by employing magnetic flux demodulation devices in the structure to increase fidelity and sonic accuracy. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The double spider design insures very high displacement and linear response while maintaining excellent control. A high order (4th) high pass filter is recommended for use with extremely high power low frequency signals. This external active high pass filter should be tuned to just below the enclosure tuning frequency. The cone has been treated with a conformal coating designed to provide additional mechanical damping and moisture resistance. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

The SD21-2000N is an ultra high output low frequency transducer. The 21 inch (533mm) diameter piston will produce extremely high sound pressure evels at very low frequencies and is ideal for high level deep bass and sub woofer response in both live sound and recorded music venues. The combination of a large radiating area and high linear displacement will generate substantial acoustic power. The operating range is 30Hz to 200Hz. The transducer uses high energy neodymium magnetics to achieve a very high acoustic output to weight ratio. The SD21-2000N employs an extremely large 6 inch (152mm) diameter voice coil that provides an AES rated 2000 watts of continuous power handling and a full 8000 watts of peak rated power handling when sufficient amplifier headroom is available. It is recommended that the transducer be loaded into a properly designed vented enclosure. The SD21-2000N utilizes P Audios Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is an inside/outside geometry with P Audios square wire technology to improve conversion efficiency and provide a very large cross-sectional area for superior cooling. System linearity is achieved by employing magnetic flux demodulation devices in the structure to increase fidelity and sonic accuracy. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The double spider design insures very high displacement and linear response while maintaining excellent control. For additional mechanical power handling it is recommended that a high order high pass filter be used and tuned immediately below the enclosure tuning frequency. The cone has been treated with a conformal coating designed to provide additional mechanical damping and moisture resistance. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

The P Audio SN15-350B is a high performance wide bandwidth transducer. The SN15-350B is an upgraded design that features many of P Audios new technologies and performance upgrades. The 15 inch (381mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses very high energy neodymium magnetics to achieve a very high acoustic output to weight ratio. The SN15-350B has been optimized for use in two way or three way sound reinforcement systems and has an operating range of 55Hz to 2000Hz. The SN15-350B features a large 3 inch (76.2mm) diameter voice coil that provides an AES rated 350 watts of continuous power handling and a full 1400 watts of peak rated power handling when sufficient amplifier headroom is available. The SN15-350B utilizes P Audios Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P Audios inside/outside wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

The P Audio SN15-500B is a high performance wide bandwidth transducer. The SN15-500B is an upgraded design that features many of P Audios new technologies and performance upgrades. The 15 inch (381mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses very high energy neodymium magnetics to achieve a very high acoustic output to weight ratio. The SN15-500B has been optimized for use in two way or three way sound reinforcement systems and has an operating range of 55Hz to 2000Hz. The SN15-500B features a large 3.28 inch (83.3mm) diameter voice coil that provides an AES rated 600 watts of continuous power handling and a full 2400 watts of peak rated power handling when sufficient amplifier headroom is available. The SN15-500B utilizes P Audios Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P Audios inside/outside wire technology to improve conversion efficiency and provide a large crosssectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

The P Audio SN15-500CX is a high performance coaxial transducer. The SN15-500CX is an upgraded design that features many of P Audios new technologies and performance upgrades. The low frequency section utilizes a large diameter voice coil design while the high frequency section employs a medium format titanium diaphragm assembly. The 15 inch (381mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses very high energy neodymium magnetics to achieve a very high acoustic output to weight ratio. The SN15-500CX has been optimized for use in two way or three way sound reinforcement systems and has an operating range of 55Hz to 20000Hz. The SN15-500CX features a large 3.28 inch (83.5mm) diameter voice coil that provides an AES rated 600 watts of continuous power handling and a full 2400 watts of peak rated power handling when sufficient amplifier headroom is available. The SN15-500CX employs P Audios under damper venting to control turbulent air flow. The voice coil design is a bobbin wound geometry with P Audios inside/outside wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The high frequency section is a close spaced titanium diaphragm assembly. The diaphragm is a 2.5 inch (63mm) diaphragm that provides excellent high frequency response and superior power handling and durability. The horn loading is provided via a thru pole piece configuration that uses the low frequency cone as part of the final horn flare. The overall high frequency design provides very high sensitivity. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.